It is run by a group of enthusiastic Kaleidescape owners and dealers purely as a service to this community.
You can dismiss this box forever by clicking the "X" in the upper right corner of this message.
... but we strongly encourage you to register for a full account. There is no cost to register for a full account.
This box goes away for registered users.
I don't suppose you've tried the 40Gbps AVPro Edge 4x2 HDMI 8K60 Matrix Switcher? I believe I am trying to address the same concerns you are, but was thinking a 4x2 matrix should be fine. And the 4x2 matrix just happens to be 40Gbps, not 48Gbps, and so maybe it will work? Of course, it would be good to understand what the root cause of your issue is -- please post here when you and AVPro figure it out!
No, I haven't. I have a few AVPro Edge devices but not that one (at least not yet). I have thought about adding it to expand the inputs available on my 4x4.
I have a Jvc nz900 hooked to an anthem avm70 8k. I can’t get a reliable hdmi 2.1 connection either. Even if I go straight from the strato k to projector it’s very unreliable. It works maybe for one video but once you go back to the desktop it loses sync and you have to reboot. The only fix that works for me is to go to hdmi 2.0 mode.
I have my Strato K connected through an Anthem AVM90 to a JVC RS3100. I was struggling to get a stable 2.1 connection. During troubleshooting, I discovered that it all worked perfectly if I use HDMI 2 out from the AVM to the projector. HDMI 1 out has problems. Tried moving it back and forth and the result is always the same. HDMI 1 out doesn't work, HDMI 2 is solid as a rock.
That kind of works. Everything gets converted to 8K by the Strato K player, all content gets unconverted and 8k is sent to the projector. Is there a way to send the native resolution of the source to the projector rather than always having the Strato k sending an 8k signal regardless of the source materials actual resolution?
Is your connection between the Strato K and the Anthem AVM90 showing up as FRL3 (24G) in the current video output from the Strato K local web server webpage?
Sorry, that I don't know. All I'm doing is moving the cable to the projector from one port to the adjacent port and getting a very different result.
Yes. On my settings page the connection shows as FRL3(24G). All content is upconverted to 8k by the Strato k player. When I called tech support they said that’s how it works. Using hdmi1 out from the anthem avm70 8k doesn’t work in 8k. Using hdmi2 out works but everything gets sent to the projector as 8k
Yes it does, at least on my system it does. When I called tech support they said that’s how it works. The Strato k sends 8k regardless of the source.
I think you must have some different settings, my Strato K does not do any video processing whatsoever and it outputs the 4KC files in the exact format they are stored in.
What you are showing me is that your system does not support 8k. It would say 4320p in the resolution area if it did. When I set my system to non-8k I get the same thing, native resolution. When I enable 8k everything gets sent 8k regardless of resolution in the file.
That's not correct. I can send 8K just fine. What do you have selected for video mode selection behavior. That is what should determine if the player does upscaling as you are seeing.
If I set it to allow changes use external scalar, the sync problems come back. But you are correct, 4K stuff gets sent 4K and 8k stuff 8k. It just loses sync easily and unpredictably when starting movies and going back to desktop. That setting is too flakey on my setup to use. If I set it to the default, allow display mode changes without external scalar it works but everything is 8k. For now that’s probably best. Letting the K do the upscaling etc.
