• Thanks for visiting the Kaleidescape Owners' Forum

    This forum is for the community of Kaleidescape owners, and others interested in learning about the system, equipment, services, and the company itself.

    It is run by a group of enthusiastic Kaleidescape owners and dealers purely as a service to this community.

    This board is not affiliated in any way with Kaleidescape, Inc.
    For official technical support, product information, or customer service, please visit www.kaleidescape.com

  • You are currently in "Guest" mode and not logged in with a registered account.

    The forum is free to use and most of the forum can be used by guests who are not registered....

    ... but we strongly encourage you to register for a full account. There is no cost to register for a full account.

    Benefits of registering for a full account:

    • Participate in the discussions! You must have a registered account to make posts on the forums. You will be able to start your own thread on a topic or question, or you can reply to other threads/discussions.
    • Use the "Conversation" feature (known as "private messaging" on other forums) to communicate directly with any of the other users here.
    • Access the Files area. The "resources" area of the forum contains many "Favorite Scene" and Script files that can dramatically increase the enjoyment of your Kaleidescape system. Go directly to great scenes in your favorite movies, created by other owners, and add automation to playback of your system with Scripts.
    • You won't see this annoying notice at the top of every screen!😊

    It's easy and free to register for the forum. Just click the "Register" button in the upper right corner of this page, and follow the instructions there.

I've done something wrong again.

flitebynite

flitebynite

Well-known member
⭐️⭐️PATRON⭐️⭐️
I am trying to replicate a disk set from my old 3U Server to my New / Main one.
Everything went well until I got the replication started.
Every title shows transfer interrupted or failed. It usually attempts each title 3 times and then moves on.
I was going to cancel the replication and start over, but the source Server has disappeared and I can't gain access to it.
I know my destination server sees it, because I get the message at the top of the user interface prompting me to see another system or add a component.
When I click on either of those links, there is nothing there.
If I shut off my source Server, those messages go away.
I've tried the simple stuff assuming a network issue: replace the cat6 Cable, Switched the network port, I even replaced the source server with the Replication disks moved into another Server unit and I'm stuck.
I have no access, The replication has stalled and I can't get in to it, stop it.
Also, I can no longer access the user interface of the source Server. Although I could before the replication attempt started.
Anyone have any ideas what I did wrong or what to do about it.
 
Current screen shot.
Does anyone know if K can stop this replication from their end?
I can't get them on the phone.
 

Attachments

  • 2021-01-05 18.20.49.jpg
    13.5 MB · Views: 11
In case anyone is interested: Yes, K can abort a replication on your Server from their end.
Thanks Rusty!
I still don't know what I did wrong...
 
I figured out why the replication didn't work.
For some reason, both of my 3U Servers are being assigned the same IP address.
If I have them both set for DHCP, why would they both be assigned 192.168.1.182?
I have since set the older Server to a static IP address and now there is no conflict.
Any insight would be appreciated.
Thanks,
Chris
 
I've been reading on line...
For all you network Guru's out there (which I am not)
Should I power cycle my Router, Switch, and all of my K devices on the network?
Will this reset all of the DHCP IP addresses?
 
Best practice would be to either set each component with a static IP address outside of your routers DHCP range, or set up DHCP reservations in your router. Pros and Cons to each method.
 
appelz said:
Best practice would be to either set each component with a static IP address outside of your routers DHCP range, or set up DHCP reservations in your router. Pros and Cons to each method.
Click to expand...
Thank you!
 
You must log in or register to reply here.
Back
Top